LL-T1
PlinEasy / OEM / ODM
4°+1
IP54
100ft/30m for Green beam
8 H/first gear 12H/second gear 16H/third gear
4*AA battries
Availability: | |
---|---|
Quantity: | |
Product Description
This Cross Line Self Leveling Laser Level adopts the bright green laser unit, with ± 1/13 inch at 33Ft high accuracy. This Cross Line Self Leveling Laser Level is the handiest and most professional laser tool you can think of to carry out work for all trades from drop ceiling installation, lighting fixtures, photo frames aligning, wall tiling down to floor tiling, etc.
Plineasy Cross Line Self Leveling Laser Level tool employed 4 AA alkaline batteries for a longer working time. The 360 laser level tool will work for 10 hours while all laser beams are on with totally new batteries.
Cross Line Self Leveling Laser Level included strong magnetic bracket enables it to be attached to metal surfaces on the wall and turn the laser level around at 360°, also offers 1/4"-20 mounting threads on the bracket and the device to suit standard tripod or pole mount.
Self-Leveling allows this cross line laser level to be used on any flat surface within 4° of horizontal/vertical. Once the level is within 4 degrees, internal self-leveling will take over and you’ll get a bright, high-accuracy horizontal and vertical line projected right where you need it. The laser will flash as a warning if it’s not within 4° of level. In manual mode, the pendulum is locked, it switches to manual mode to lock lines for use at any angle.
Plineasy Cross Line Self Leveling Laser Level has two laser sources. Projects bright horizontal, vertical & cross 3 mode lines onto flat surfaces and levels by one-button operation. Pulse mode extends the working range up to 200Ft with a laser receiver.
Laser Wave length | Red beam:635nm |
Green beam:505-530nm | |
H/V Accuracy | ±2mm/10m |
Self-leveling range | 4°±1° |
Working Range | Green: 30m/ Red: 15m |
Power supply | 2*1.5V AA |
Operating temperature | -10°C to 50 °C |
Mount Size | 1/4-20 mounting thread |
IP Rating | IP54 |
1 x Magnetic Fine-Tuning Bracket, 1 x Carry On Bag, 1 x User Manual, 1 x Cross Line Self Leveling Laser Level, 4 x AA Batteries
When the T1 Cross Line Self Leveling Laser Level instrument is working, short-press key button, the instrument enters the energy-saving mode, and the brightness is reduced to about 50% of the maximum brightness;press it again to reduce it to 25%; press again to restore the maximum brightness cyclicall.
This T1 Cross Line Self Leveling Laser Level, with double condenser lens, objectmodes, and three modes of horizontal or vertical or cross line laser can be selected.
Self-leveling within 4 degrees, and manual mode, ideal for tilting laser lines manually at any angle. You can switch it at will and measure the dead angle for you.
Rubber protection coating makes the level more robust and durable. IP54 water/dust resistance ensures you work well in hazardous working conditions.
T1 Cross Line Self Leveling Laser Level has double condenser lens , object modes Horizontal or vertical or cross line laser can be selected , It projects one 130° Horizontal and one 150° Vertical line for a wide array of leveling and alignment applications.
TT-T1 Cross Line Self Leveling Laser Level is the most handy and professional laser tool you can think of to carry out work for all trades from drop ceiling installation, lighting fixtures, photo frames aligning and wall tiling down to floor tiling etc.
A1: No. Laser has a magnetic holder. It can setting in a camera tripod too.
A2: Yes indeed
A3: Its ok
A4: It is very sensitive the level light so have to be pretty static
A5: Moderate.... depends on how long you leave the light on each time. When battery is weak, will auto-off after short time.
A6: Move the slide switch under the laser light to the left.
A7: I had the same question at first. The pulse typically indicates that the level is more than 4 degrees out of level, and can't correct. Try getting the unit closer to level. Most likely the pulse will go away. you can then use the pulse to indicate to you that you need to get the unit closer to level before turning it on. I have not had any problems once i learned this.